Unistrut P2225 Cross Reference: B-Line B121, Superstrut A217, Power-Strut PS 667
Unistrut P2225 cross-references to B-Line B121, Superstrut A217, Power-Strut PS 667 and Haydon A-326-1. The cited guides list these numbers together as candidate substitutes. That carries no load rating, listing or steel grade: each manufacturer publishes those separately, and they do not travel with a part number.
By Alex · Last reviewed 2026-09-15 · Spec looks wrong? Tell us.
What a published cross-reference number does and does not cover
A published cross-reference number is one thing only: a number a cited document prints opposite this one, as a candidate substitute in the same catalog slot. We have not independently verified any competitor part's dimensions or interchangeability.
It does not carry design loads, safety factors, steel grade, coating thickness or third-party listings — UL, cUL, FM, seismic. Each manufacturer publishes those independently, and two parts that measure identically can carry different published loads. Finish suffixes differ by brand as well, so order the base number and state the coating in words.
Where a specification names a brand, a substitute is a submittal question, not a purchasing one: send it through as an or equal with the substitute's own load and listing data, and get it accepted in writing before it ships.
Unistrut P2225 — published cross-reference part numbers
P2225 is a nine-hole wing fitting, 3-3/4 in. wing on a 3-7/8 in. body — Wing fitting, 3-3/4 in. wing x 3-7/8 in. (95.3 x 98.4). Every value below is copied out of a published cross-reference document; the tag in the source column names it, and the Sources list gives the title, URL and access date.
| Brand | Published cross-reference part number | Source |
|---|---|---|
| B-Line | B121 | [S1], [S3], [S4] |
| Superstrut | A217 | [S1], [S3] |
| Power-Strut | PS 667 | [S1], [S3] |
| Haydon | A-326-1 | [S3] |
No competitor dimensions are published on this page. We hold verified dimensional data for the Unistrut part only, so this table carries part numbers and their sources and stops there.
What to check on a substitute
A cross-reference table gets you a part number. It does not tell you whether the thing in the box lines up with the holes you already have. These are the numbers that decide that for P2225 — 4 checks, each with the Unistrut figure and the catalog page it is printed on. Work through them before the run goes up.
| Measure | Unistrut value | Why | Where the number comes from |
|---|---|---|---|
| Overall size | 3-3/4 in. wing x 3-7/8 in. (95.3 x 98.4 mm) | P2224 on the same catalog page is the same body with a 1-7/8 in. (47.6 mm) wing. The wing dimension is what tells the two apart in a bin. | Unistrut® General Engineering Catalog no. 17, p. 110 — printed on the part drawing |
| Hole count | 9 — 3 in the top, 6 in the face | Count them before anything else; the hole count is the fastest mismatch to spot. | Unistrut® General Engineering Catalog no. 17, p. 110 — printed in the part table |
| Hole center to hole center | 1-7/8 in. (47.6 mm) | The figure the p. 110 page header gives for this fitting. Measure it between two adjacent hole centers inside one row, not across the bend. | Unistrut® General Engineering Catalog no. 17, p. 110 — standard-dimensions note in the page header |
| Material thickness | 1/4 in. (6.4 mm) | Sets the grip length of the bolt. | Unistrut® General Engineering Catalog no. 17, p. 110 — standard-dimensions note in the page header |
These are the Unistrut figures, published here so you have something to measure against. They are not a claim about any other manufacturer's part.
What we can quote against this part number
We do not manufacture these parts and we are not Unistrut. We source them. The item we can quote against Unistrut P2225 is Wing fitting, 3-3/4 in. wing x 3-7/8 in. (95.3 x 98.4) — a candidate substitute made to order by a contract manufacturer, offered for inquiry, not an original-manufacturer part.
| Dimension | Value | Source |
|---|---|---|
| Size | 3-3/4 in. wing x 3-7/8 in. (95.3 x 98.4 mm) | Unistrut® General Engineering Catalog no. 17, p. 110 — printed on the part drawing |
| Holes | 9 (3 top + 6 face) | Unistrut® General Engineering Catalog no. 17, p. 110 — printed in the part table |
| Width | 1-5/8 in. (41.3 mm) | Unistrut® General Engineering Catalog no. 17, p. 110 — standard-dimensions note in the page header |
| Thickness | About 0.23 in. (5.8 mm) base steel before coating; a hot-dip galvanized part measures thicker. Steel grade confirmed at quotation. | Our supply specification — not a catalog figure |
These are the published Unistrut catalog dimensions we build to, each with the page it is printed on. The thickness row is the exception: it states what we supply, not a catalog figure. They are geometry only. No load, torque or listing figure is claimed for our part: none has been tested on it, and a figure published for a Unistrut part is evidence about that part, not about ours.
Every published dimension with the catalog page it is printed on, the finishes, and what to measure on a delivery: P2225 part page.
Get this part number quoted
Answer the seven lines below and we come back with our part number, finish options, lead time, packing quantity and what documentation we can and cannot supply. There is no list price — it is quoted per mill, finish and volume. The form takes about a minute and already knows this part number. We reply within one business day (Asia/Shanghai, UTC+8).
- Unistrut part number — P2225
- The brand and part number you are replacing
- Finish
- Quantity
- Destination — country, and state or ZIP if US
- Application — general support, electrical, mechanical, seismic, or a listed assembly
- Whether you need submittal documentation
No minimum order · 5–7 business days ex-factory · Reply within one business day (Asia/Shanghai, UTC+8) · Finishes: plain, EG, HDG, stainless
Prefer email? Open a prefilled RFQ in your mail client, or write to contact@channelstrut.com yourself. If the part is going into a specification that names a brand, say so — a substitute has to be accepted in writing before it ships.
Trademarks and who we are
Unistrut, B-Line, Superstrut, Power-Strut and Haydon, and the part numbers published under them, are trademarks or trade names of their respective owners. ChannelStrut is not affiliated with, authorized by, endorsed by or a distributor for any of them. Those brand names and part numbers are used here only to identify the products referred to.
ChannelStrut is run by Alex, a hardware sourcing specialist based in Fujian, China. We do not manufacture these parts — we source them from the mills that produce them. More on how the data is built: About.
Sources
The cross-reference part numbers on this page come from S1, S3 and S4. The dimensions come from the Unistrut® General Engineering Catalog no. 17; the page number is printed against every one of them above.
- S1
- Divspec - Strut Fitting Cross Reference (Divspec / B-Line / Unistrut / Powerstrut / Superstrut(Thomas & Betts))
http://www.divspec.com/strut-fitting-cross-reference/
third-party aggregator · accessed 2026-09-09 - S3
- Master Distribution - Part Number Cross Reference Guide (G-Strut / Unistrut / Powerstrut / Superstrut / Erico / B-Line / PHD / Haydon), 23 pages
https://masterdistrib.com/content/PDF/Masterdistrib_Part_Number_Cross_Reference_Guide.pdf
third-party aggregator · accessed 2026-09-09 - S4
- Cooper B-Line - Strut Systems Competitor Cross Reference (BF93XR): Unistrut pp.2-12, Power-Strut pp.13-19, Superstrut pp.20-29, Kindorf pp.30-34
https://usermanual.wiki/Pdf/499295Brochure.1451337879.pdf
manufacturer (Cooper B-Line, now Eaton) · accessed 2026-09-09 · link dead, no archive
Source link no longer resolves; we keep an archived copy.
Every source above was re-checked for reachability on 2026-09-15.
Back to the full cross reference — 126 part numbers, or read P2225 in context there: row P2225.